Installation planning · 4 min read

LED Skirting Boards: Selection and Installation Planning

Compare AURON LED, REGENT LED and VIREO LED. Plan wall integration, lighting components, driver access and sample approval without assuming electrical ratings.

AURON LED — Application illustration
AURON LED · Application illustration

An LED skirting detail combines an architectural profile with a lighting assembly. Select both together. A section that suits the room visually still needs compatible lighting components, an agreed wiring route and practical access for maintenance.

This guide covers the existing AURON LED, REGENT LED and VIREO LED references. It is a planning guide, not an electrical installation specification or evidence that a particular strip, driver or diffuser combination has been approved.

Compare the three model references

AURON LED has a flat face with upper and lower illumination; REGENT LED uses a more classical contoured face with upper and lower illumination. Their current drawing references give 100 × 13 mm and 100 × 20 mm respectively for height and projection. VIREO LED is another dedicated model whose section and light-channel arrangement should be checked on its own product drawing. Compare the visible contour, projection and wall relationship before treating the models as interchangeable.

Define the intended lighting effect

Explain whether the detail should illuminate the wall, the floor junction or both, and review a sample in the proposed room conditions. The visible result depends on the complete assembly and its placement, not only the aluminium face. A lighting designer or qualified electrical professional should specify the strip, driver, control arrangement and required performance. The catalogue does not confirm strip width, voltage, power, IP rating or supplied electrical components. Do not fill those gaps with values from a competitor's LED profile.

Plan access before closing the wall

Agree the wiring route, driver position and a means of accessing serviceable components before wall work conceals them. Establish which trade supplies and installs each element, and document the handover between the profile installer and electrical installer. Check the actual diffuser and cover arrangement against the selected model. Progress Profiles' LED skirting documentation is an industry example of a system with coordinated accessories; it does not establish compatibility with AURON, REGENT or VIREO.

Technical reference: Progress Profiles: PROSKIRTING LED technical sheet

Approve a model-specific sequence

Use the selected product's installation material to agree the order of carrier fixing, lighting installation, testing and fitting of the visible cover. Some existing model guidance discusses surface-mounted or flush integration, but the wall build-up still needs project-specific coordination. Resolve the corner and closure detail before cutting. Where source instructions give more than one fixing approach, ask which is appropriate for the substrate. Do not assume an adhesive mentioned in general guidance is approved for every site condition.

Build a representative mock-up

The mock-up should include a straight run, a corner, an end and the proposed lighting components. Review the illuminated result from normal viewing positions and check access without damaging the finish. Ask the responsible lighting professional to confirm the electrical assembly before installation proceeds. Record the approved profile, finish, component references and any maintenance procedure. This creates a useful acceptance reference for both a project order and a distributor's demonstration installation.

Separate profile supply from the lighting package

The enquiry should identify exactly which mechanical and electrical components are requested. Do not assume a product photograph means that strips, drivers, wiring or every accessory are included. Confirm the supply-length conflict recorded on affected model pages before calculating quantities. Keep profile quantities and lighting requirements as separate schedule items, then reconcile them against the approved assembly.

  • Model, drawing revision, wall detail and finish sample.
  • Lighting effect and responsible electrical specification.
  • Confirmed strip, driver, diffuser and control compatibility.
  • Access arrangement, component inclusions and confirmed supply lengths.

Plan the profile and lighting system together

AURON LED, REGENT LED and VIREO LED are aluminium profiles designed for LED integration. The configuration below is project guidance, not a declaration of supplied components, electrical ratings or certification for these models.

Bare aluminium profile

A non-electrical profile for integration into a lighting design. Confirm the profile, diffuser and fixing scope; do not assign voltage, lumen output or an IP rating to the bare extrusion.

Profile with selected components

Specify the LED strip, diffuser, driver and controls individually. Confirm dimensional fit, heat dissipation and electrical compatibility before combining them.

Complete assembled lighting product

Agree the complete assembly and responsible manufacturer. Electrical ratings, instructions, testing and applicable conformity documentation must relate to that actual assembly.

Project-selectable configurations

Light and colour
Possible design targets include 2700K or 3000K warm white, 4000K neutral white and high colour rendering such as CRI Ra ≥90. Confirm the selected LED component and approve the lighting effect.
Power and control
A 24V DC constant-voltage LED system is one possible configuration. Select strip power in W/m, total run length, voltage drop and driver capacity together. Use a compatible constant-voltage driver where required by the strip; agree a compatible dimming system.
Integration and access
Check strip and diffuser fit without assuming a model-specific strip width. Assess operating temperatures and heat dissipation in the installed assembly. Keep drivers, connections and replaceable components accessible for maintenance.
Installation environment
Specify project-specific IP protection for the complete assembly, including joints and connections. A strip or driver IP rating does not automatically establish the rating of the installed lighting system.
European technical framework

IEC 60598-1 concerns luminaire safety; IEC 62031 concerns LED-module safety; IEC 61347-1 and IEC 61347-2-13 concern controlgear safety. IEC 60529 defines enclosure IP classification. The applicable EN edition, relevant particular standards and product classification must be confirmed for the selected assembly.

EU Regulation 2019/2020 addresses ecodesign for in-scope light sources and separate controlgear; EU Regulation 2019/2015 addresses light-source energy labelling. A bare aluminium profile is not itself a light source. Assess containing-product obligations for an assembled system.

Assess the Low Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU and RoHS Directive 2011/65/EU according to the supplied electrical product. A 24V DC circuit is below the LVD voltage range, but its mains-powered driver may be in scope; this does not remove other applicable safety obligations.

CE marking is a manufacturer's declaration under applicable legislation, not a general quality certificate. These references do not certify FIRST METAL models. Confirm the final bill of materials, current applicable EN standards and supporting documentation before specifying a complete lighting product.

Technical references and scope

Frequently asked questions

Which voltage or IP rating do these models have?

The current profile records do not establish those electrical specifications. Confirm the complete lighting assembly and its suitability through the responsible supplier and electrical professional.

Are LED strips and drivers included?

Inclusion is not confirmed by the profile references. State the required components in the enquiry and request an explicit supply breakdown.

Discuss your project detail

Send the profile reference, application, drawings and quantity requirements. Include the points from this guide that need confirmation for your project.

Technical references and scope

Product-specific information comes from the linked FIRST METAL catalogue records. External manufacturer examples explain principles; their dimensions, ratings and compatibility are not transferred to FIRST METAL products.

WhatsApp